30-Amp Pro Switch-Mode BEC Brushless ESC
Prodotti simili
E-flite’s 30-amp Pro SB brushless ESC offers up to 30 amps of continuous current with proper airflow and a peak of 35 amps. It drives up to 5 analog or 4 digital sub-micro servos with the BEC on any recommended input voltage. This brushless ESC includes programmable motor braking, soft start for helis and planes, timing, throttle input range, and low-voltage cutoff. It also features auto motor shutdown in case of lost signal or interference. The safe power-arm mode prevents accidental starts.
- Up to 30-amp continuous current with proper airflow, 35-amp peak
- 5-volt Switch-Mode BEC circuit capable of 700mAh continuous current on any recommended input voltage
- Drives up to 5 analog or 4 digital sub-micro servos with the BEC
- 3S-4S Li-Po or 9- to 12-cell Ni-MH/Ni-Cd input voltage
- Programmable motor braking
- Safe power-arm mode prevents accidental starts
- Programmable low voltage cut-off with settings for 3S Li-Po (9.2V), 4S Li-Po (12V) or 74% of battery starting voltage
- Programmable soft start for helis and airplanes
- Auto motor shutdown if signal is lost or there is interference
- Programmable timing - 5 user-selectable ranges for use with a larger variety of brushless motors
- Heli mode for starting the motor with a low speed ratio
- Optional RS232 Serial Link available for programming (EFLARS232)
- Pre-wired connectors - E-flite EC3 connectors on battery input and 3.5mm female gold bullets on motor output leads
- Brake: Yes
- Continuous Maximum Current: 30A
- Input Voltage: 3S–4S Li-Po, 9- to 12-cell Ni-MH/Ni-Cd input voltage
- Input Connector Types: 16AWG with E-flite EC3 connector
- Output Connector Types: 16AWG with 3.5mm Female Gold Bullet Connectors
- Momentary Peak Current: 35A
- Dimensions (WxLxH): 28mm (1.1 in) x 51mm (2 in) x 8.7mm (.35 in)
- Weight: 31 g (1.1 oz)
- BEC Voltage: 700mA continuous
Tech Notes
Servo Ratings with BEC Enabled:
Drives up to 5 analog or 4 digital sub-micro-sized servos with the BEC on any recommended input voltage.
Some servo combinations we have tested in various models include:
- 1 analog standard servo, 1 digital sub-micro servo, 2 analog sub-micro servos—E-flite Apprentice 15e RTF
- 2 ParkZone (PKZ1081) analog sub-micro servos and 2 ParkZone (PKZ1090) digital metal gear sub-micro servos—ParkZone T-28 Trojan RTF & F4U Corsair RTF
Some other brands and models of servos may have significantly higher current draw. Digital servos and binding servos of any kind typically have higher current draw. As a general rule, micro and sub-micro servos draw less current which may affect your servo usage as shown in the examples above. We recommend the use of a Hangar 9 Servo and Receiver Current Meter (HAN172), installed between the throttle lead of the ESC and receiver, to confirm current draw of the actual servos used. Also, always
be sure to position the ESC for maximum airflow since cooling can significantly aid in the performance of the BEC.
Before first use, please refer to “Servo Ratings with BEC Enabled” notes for BEC usage guidelines. You must follow these guidelines for safe operation. If you are using more than 5 analog sub-micro-sized servos, more than 4 digital sub-micro-sized servos, or servos with higher current draw than the BEC can deliver, you will need to disable the BEC. If you wish to disable the BEC, you must remove the red receiver wire lead and connector from the receiver lead housing, and then insulate it properly to prevent shorting. When operating with the BEC disabled, E-flite recommends the use of a separate, high-power, external BEC (like the Ultimate BEC), or receiver pack and switch using the following items to ensure trouble-free operation:
1. JR 1100mAh 4.8V Ni-MH receiver battery (JRPB4240),
or similar
2. JR Switch Harness (JRPA003), or similar
