T-12 Z + R6014 HS 12-Channel 2048 2.4GHz Computer System

Summary extract of Functions:

General

• Model memory, 25 internal model memories, extending to approx. 240 models per 32MB memory storage on a Data-Pack (Compact Flash) card, CF card upto 1000 MB.
• Model name with 8 and user-name 12 characters.
• Free choice of function and additional function names.
• Operating hours timer, clock and calendar function, two stopwatches with 100 lap time and motor run time memories.
• Free transmitter control assignment for channels 1 … 14, mode select throttle left/right
• 12 Twelve proportional channels, 2 switched channels, 2 proportional channels can be expanded to eight multi-channels each using Multi-Prop decoders.
• Function reverse for all channels, plus hardware transmitter control reverse.Trainer mode with single function transfer and mix operation
• Digital stick trims, with a choice of normal, centre or ATL (asymmetric) trim functions. Choice of group mode (effective in all flight modes) or single mode, (effective only in a relevant flight mode).
• For each control (also switches and sliders), there is a free selection of trim control, using a digital button or analogue rotary knob/ linear sliders
• Servo end point adjustment (ATV) on all 12 proportional channels
• 4 stick functions, 8 switches, 3 rotary control knobs.
• Free choice of control and the sequence for the 12 proportional- 2 switch -and 4 virtual channels. Up to 6 switchable Dual Rate settings for each function. Alternatively, pre-programmed transmitter control settings from linear, via exponential, up to 9(or 17) -point curve. Separately variable speed setting and delay for both directions ("there and back"). Choice of group mode (effective in all flight modes) or single mode, (effective only in relevant flight mode).
• 8 flight modes per model memory with selectable priority, any name can be assigned to a mode.
• 10 freely programmable mixers per model memory. Pre-programmed transmitter control settings available to user, from linear to 9-point curve (can be expanded to 17 points). Optionally with / without trim. Mixer mode "Stick to Stick" or "Stick to Servo"
• Separate delay and speed settings for switching mixers on and off. Mixers can be set-up to operate sequentially (cascading), switches, stick functions or virtual functions can be selected as transmitter controls.
• Offset function and fine adjustment using external mixer adjustment via rotary knob, switch or stick. Optional group mode (effective in all flight modes) or single mode, (effective only in a relevant flight mode).
• Alternatively, each programmmable mixer can be switched from a curve mixer to – Offset mode. This Offset mixer permits the mixing of up to 4 Offset values per programmable mixer, with separate delay and speed settings for switching mixer to affect freely selectable functions.
• Naturally, these mixer functions can also be activated in group mode (effective in all flight phases) or in individual mode (effective only in relevant flight phase).

Power Models (Acro)

• Comprehensive mixer menus for an enormous range of power model types, from aircraft with one aileron servo up to eight wing mounted servos.
• In addition to the wing type, the user can also select from the following tail variants: normal, separate elevators with aileron function (taileron) and V-tail... Deltas and powered flying wings with 2 … 8 wing-mounted servos are also available. These mixer menus are pre-programmed to suit the model type, and contain all the essential mixer functions as standard.

Model gliders (Glider)

• Comprehensive mixer menus are also available for a huge range of sailplane types, from gliders with one aileron servo to types with up to eight wing-mounted servos. Optionally with or without motor.
• In addition to the wing type, the user can also select from the following tail variants: normal, separate elevators with aileron function (taileron) and V-tail... Flying wings with two to ten wing-mounted servos can also be selected. These mixer menus are pre-programmed to suit the model type, and contain all the essential mixer functions as standard.

Model helicopters

• The basic difference between the various mixer menus for model helicopters is the method of swashplate actuation. All the classic linkage types are included as standard: H1, H2, HR3, HN3, H4 and the new H3 90° and H3 140° Every imaginable mixer function is available in these menus.
• A special feature is the new form of variable pushrod travel compensation for the H3 and H4 types. This function eliminates a common problem found with unequal travels, which can result in servo damage can occur in the long term, when travels are fairly large or asymmetrical. The speed of the pitch-axis (elevator) function can also be adjusted, in order to avoid the run-time differences with the HR3/HN3 120° swashplate linkage.
• With integral virtual swashplate rotation.
• Gas Limiter Function